[Kunkka]

No one here can state what would or wouldn't be standard for a trim level in your country as the spec varies for every country. I can say the version of TPMS that displays the individual pressures is normally an extra cost option, requiring transmitters in each wheel, and a receiver module on the car. Therefore if the display doesn't obviously show, it's likely you have the standard TPMS which will warn you of a leaking tyre, and tell you which one, but not show you the actual pressures.

Aha, ok, in that case it is standard TPMS which you mentioned because it displays menu for calibration, but it doesn't display values.

 

[iangaryprice]

On my Tiguan with the basic Tyre pressure monitoring.It can only be reset using the steering column stalk and the MFD in the middle of the dash.

 

[j.wollschlaeger89]

Hi,
Father parked the car in the garage. He left the keys in the ignition. The lights stayed on. In the morning, the car was discharged. I had to disconnect the battery. I immediately charged the battery so that it would not be destroyed.
Since then, the pressure light has been on.
VCDS displays an error:

Address 19: CAN Gateway Labels: 7N0-907-530-V2.clb
Control Module Part Number: 7N0 907 530 AN HW: 7N0 907 530 AN
Component and/or Version: J533 Gateway H56 1642
Software Coding: 356002
Work Shop Code: WSC 01357 011 00200
VCID: 7CF741F7FFEB6E645E-8028
1 Fault Found:
01325 - Control Module for Tire Pressure Monitoring (J502)
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00110100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 197
Mileage: 130359 km
Time Indication: 0
Date: 2039.14.07
Time: 17:37:33

At that time, the display showed the tire pressure.
I don't have it displayed now.
I tried disconnecting and connecting the battery again, erasing the error but nothing.
Anyone have an idea?
View attachment 33165

Hello, I hope the translator is doing everything right ... I'm from GER and have exactly the same problem ... . Tire pressure indicator lights up permanently and the display or menu item Show tire pressures in the instrument cluster has disappeared... have you found a solution?

 

[Roy01]

I came across this problem also. I installed tyre pressure module antenna 3AA 907 273 D with tyre pressure sensors 3AA 907 275 F in a VW Scirocco.

The problem is these pq35 platform models use a bcm with built in TPMS, they work with different sensors. If you check byte 8 bit 7 (on my bcm) direct TPMS PR-7K3/4/5 installed in bcm module 09 it will listen to other sensors I think. So just uncheck it. I also made thé same mistake and lost the tpms screen in thé cluster and tpms warning light coming on by doing this.

I had the same problem after the repair shop fixed one of my tyres.
In your case I would revert to the stock coding. Then cycle the key. Try to deflate all of the tyres to 1 bar and then immediately inflate to the correct pressure to wake up the sensors.
Then take it for a longer drive so thé system relearns the tyre positions.
The error will then clear itself.

I read some stories about undervoltage damaged tpms module I hope this isn’t the case.

Hope it helps.

 

[miso6322]

I solved the problem, I replaced the unit 3AA 907 273 D. I don't know why it went away. After replacing the new unit, everything works.

One problem here is:
My tire size is just not on offer. How do I add the size: 235/55 R 17 to the menu?

 

[tricky]

Sounds like the control module that receives the tyre signals has either gone to sleep or permanently dead. It may be possible to reset it by clearing the error on the module using e.g. OBDeleven, or else it may need a dealer action.

So I called it then . Glad you've got it sorted. Sorry, don't know about setting the tyre sizes. You have VCDS can you look around the settings and adaptations see if there's any clue there?

 

[IggytheTiggy]

Just choose the one with the closest rotational diameter. I don’t believe even with vcds there is a way to add. It still monitors all four rotations if one is going flat the diameter changes and triggers the light and warning.

 

[miso6322]

I couldn't find anything similar to my needs in VCDS. Apparently, this setting is done through another diagnostic, but I don't know how.
It shows the measured pressure but the recommended pressure is shown as 2.9 but for me it should be 2.5. But that doesn't matter, the system works.