VW Tiguan Forum banner
1 - 20 of 175 Posts

·
Registered
Joined
·
878 Posts
Discussion Starter · #1 ·
Hello

I have a Tiguan 2011 no facelift....

I have change my windshield front glass 5N0845011N NV so i can fit lane assist camera 3AA980654D

I have also change gateway to 7N0907530AN supporting CAN-Extended.....

I have connect everything from the camera....

ground

+12V

but were must i connect the 2 wires canbus???

i connected the canbus wire in to gateway connector pin 17 and 7 that was free from wires You can see picture

i dont have any connection in vcds in my camera......

can anybody help me with this??
 

Attachments

·
Registered
Joined
·
878 Posts
Discussion Starter · #3 ·
i have activated A5 in CAN but it seems that i cant communicate with it.......
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #4 ·
ok now it works with the communication with the

3AA980654D

i can see now the lane assist in the mfd but i can not check it, when i do it i hear the sound "cling" and it becomes unchecked

i think i must calibrate it......
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #6 ·
I will design my own the board not so hard....

and i have not updated module 44 Steering Assist....
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #8 ·
no i don't have this.....you don't need to change this...

yes i have error in VCDS

this is probably because the lane assist must be calibrate so....
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #9 ·
Gateway Installation List: 7N0 907 530 AN

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
14-Susp. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: Malfunction 0010
1C-Position Sensing -- Status: OK 0000
20-High Beam Assist. -- Status: Cannot be reached 1100
22-AWD -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
3C-Lane Change -- Status: Cannot be reached 1100
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: OK 0000
5C-3C-Lane Change -- Status: Cannot be reached 1100
62-Door, Rear Left -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
77-Telephone -- Status: OK 0000
A5-Frt Sens. Drv. Assist -- Status: Malfunction 0010
 

·
Registered
Joined
·
878 Posts
Wednesday,04,November,2015,21:38:32:33490

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------

Chassis Type: 5N (7N0)
Scan: 01 02 03 08 09 14 15 16 17 19 1C 20 22 25 3C 42 44 46 52 53
55 56 5C 62 72 77 A5

VIN: WVGZZZ5NZBW031598

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
14-Susp. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: Malfunction 0010
1C-Position Sensing -- Status: OK 0000
20-High Beam Assist. -- Status: Cannot be reached 1100
22-AWD -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
3C-Lane Change -- Status: Cannot be reached 1100
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
53-Parking Brake -- Status: OK 0000
55-Xenon Range -- Status: OK 0000
56-Radio -- Status: OK 0000
5C-Lane Maintain. -- Status: Cannot be reached 1100
62-Door, Rear Left -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
77-Telephone -- Status: OK 0000
A5-Frt Sens. Drv. Assist -- Status: Malfunction 0010

-------------------------------------------------------------------------------
Address A5: Frt Sens. Drv. Assist (R242) Labels: 3AA-980-654.clb
Part No SW: 3AA 980 654 D HW: 3AA 980 654 A
Component: MFK_Gen1 H09 0300
Serial number: 0187631669
Coding: 010102010102020F0000040000010000
Shop #: WSC 13231 210 00200
ASAM Dataset: EV_47X 001639
ROD: EV_47X.rod
VCID: 397F5BBFB8DB40D69C3-806C

3 Faults Found:
2621440 - Databus
U1121 00 [009] - Missing Message
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 0
Mileage: 20062 km
Date: 2030.14.31
Time: 00:50:08

2686976 - Databus
U1121 00 [009] - Missing Message
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 0
Mileage: 20062 km
Date: 2030.14.31
Time: 00:50:08

6488064 - Steering
C10AC F2 [009] - Lane-Holding Assistance Not Coded
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 0
Mileage: 20062 km
Date: 2030.14.31
Time: 00:50:08
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #15 ·
manage to activate lane assist......try now on the road......

but i have still errors that i must try to resolve...

5khjs9.jpg
 

·
Registered
Joined
·
1,803 Posts
Remove this:

3C-Lane Change -- Status: Cannot be reached 1100

(Tiguan doens't have this option, it needs a different cluster, not even new 3d clusters are compatible with this)

20-High Beam Assist. -- Status: Cannot be reached 1100 (I think this is the mirror from picture) What you should check is Byte2 from camera

1860_1.jpg
 

·
Registered
Joined
·
878 Posts
Discussion Starter · #18 ·
The thing is when you try to put something in VCDS for the camera you MUST turn off ignition and turn it on again so you see what you did.(i didn't do this from the beginning)

Modul 44 coding was not missing, it was there all the time...

I was in the adaptation in camera and did some adjust...that I have reading in Russian forum.....

ok I will remove 3C-Lane Change in gateway but I think 20-High Beam Assist will work, I must read about it more.....

I always had auto light. ..

yes I connect windows defogger...you must do it...the cable is ON the glass original and you connect them in the camera connector, this is easy.....
 

·
Registered
Joined
·
1,803 Posts
when I wrote Auto I mean Beam assistant because symbol is "A" with light.

You're also following Drsedoy work, very good!!!

The high beam assist works but from A5 module, not 20. Check byte 2

I don't know if you read that part but he changed BCM to have Beam assistant.

Coding: 010102010102020F0000040000010000

I think 02 is for resltyle Xenon, I believe you have to put 01
 

·
Registered
Joined
·
405 Posts
I have HBA on module 20, can anything be done with regards to lane change etc with this module or is it just the other way round whereby the lane change camera can be used for HBA (saw this on Skoda forum for new MK3 Octavia).
 
1 - 20 of 175 Posts
Top